Description
Features:
JINGYAN MESR-100 V2 Auto-ranging capacitor ESR and Low Ohm Meter, measuring range from 0.001 to 100.0R, support IN CIRCUIT Testing.
Using true 100 KHz sine wave to measure the ESR value, which is equal to the testing method of capacitor manufacturer.
In the market, there is some technique using short pulse method to testing, but the value will be varying vs the capacitance and sometimes reading is different from the manufacturer's value.
What is ESR of capacitor?
There is a series resistor inside capacitor, using 100kHz to remove the impedance 1/(2*pi*F*C), the impedance become small, and we can then measure the true series resistor value.
A bad E-capacitor will have larger ESR and create large ripple rather than filtering noise. Normally, a big capacitor is larger than 3 ohm.
Using this theory, we can measure the capacitor is bad/ damaged or good in condition.
Because our ESR meter only applies less than 15mV DC or peak to peak on a good capacitor, as a result we can use it as in circuit test. Because this low testing voltage, it cannot turn on the semiconductor inside a circuit under testing.
During repairing TV, LCD, Audio board, etc. we can in circuit testing the capacitor is good or not.
Dual terminal, for fast and easy inspect general capacitor or resistor, a printed ESR table for fast check
Compare MESR100 old V1 and new V2 Improvement:
1) Change square wave to sine wave 100 KHz, reduce square wave¡¯s high frequency component, and affect the reading passing the test leads and capacitor.
2) Higher Resolution up to 0.001 ohm.
3) 128X64 dot matrix LCD, with more larger value display and information
4) Embedded 25V capacitor table at LCD, auto display the capacitor is good or bad reference to common 25V electrolytic capacitor.
5) New plastic case, curve design for hand carrying. New stand for 60 degree stand on desk.
6) Use 2X AA battery, more convenience and longer battery life than 9V battery.
7) Support external USB power, using standard micro-USB port.
Specification:
Range
Accuracy (After Zero, tested with 1,10,100R resistor)
Refresh Time (Manual Mode)
Auto mode take 0 to 2s more time depend on value
0.000 to 1.000R 1%+2Digit ~0.4s
1.000 to 10.00R 1%+1Digit ~0.4s
10.00 to 100.0R 2%+1Digit ~0.4s
Accuracy maybe affected by the test lead¡¯s length and contact point resistance.
Standard test leads is 15cm, for longer test leads need special shielding to affect the EMI inference (Can contact sales¡¯ person for more detail)
1) Accuracy: Up to 1% (detail on above table)
Wide Measurement Range: >1uF (for 0.1uF the error will be larger on equation 1/(2*pi*F*C) @ 100Khz )
2) High Resolution: 4 digit, or 0.001Ohm @ 1 Ohm range
3) Measuring voltage: <~40mV RMS (TESTING VOLTAGE)
4) Clamping voltage: ~0.15V (open voltage)
5) Battery 2X AA 1.5V battery
6) External Power: 5V micro USB
7) Operating current 0.02A
8) Battery Life time: >80 Hours
Operating Introduction:
1) POWER ON
Press and hold the ON/ OFF circle orange button for 2 to 3 second to power on.
Press and release the ON/ OFF button to shut down meter.
2) AUTO/ MANUAL mode:
i) Auto Range:
Press and release the RANGE button and at the first line of LCD will show ¡°AUTO:"
At auto mode meter will automatically select the best range to detect.
ii) Manual Range:
Scroll the manual range from 1R, 10R and 100R range by press and release the RANGE button
In LCD will show MANUAL at first LCD line and show at second line: 0-1R, 1-10R and 10-100R.
3) 1 Key Zero:
Short circuit the test leads¡¯ terminal, cancelling the wire resistance.
Press and release the ¡°ZERO" button, LCD shows ¡°ZERO" and wait the zero disappear.
If you are using the meter array socket, you need to use a short pin to short circuit to set zero.
4) Backlight:
LCD backlight will on during power on
5) Auto Sleep:
Around 10 hours for not testing, it will shut down automatically to save power.
6) OVERFLOW or OL:
Display overflow when the value is out of range, you can check that you are zero correctly.
7) ESR TABLE:
It is for reference only, different manufacturer of capacitor has different ESR, better to test a good cap ESR and compare with what you are testing, usually bad cap with higher ESR few times larger than good one.
8) SOFTWARE ESR:
Put the 25V Electrolytic capacitor value to LCD, and compare,
GOOD if C < XXuF, means the capacitor maybe good condition if it is less than XXuF
9) PLASTIC STAND:
If you don¡¯t use the stand, press and push the lock position
JINGYAN MESR-100 V2 Auto-ranging capacitor ESR and Low Ohm Meter, measuring range from 0.001 to 100.0R, support IN CIRCUIT Testing.
Using true 100 KHz sine wave to measure the ESR value, which is equal to the testing method of capacitor manufacturer.
In the market, there is some technique using short pulse method to testing, but the value will be varying vs the capacitance and sometimes reading is different from the manufacturer's value.
What is ESR of capacitor?
There is a series resistor inside capacitor, using 100kHz to remove the impedance 1/(2*pi*F*C), the impedance become small, and we can then measure the true series resistor value.
A bad E-capacitor will have larger ESR and create large ripple rather than filtering noise. Normally, a big capacitor is larger than 3 ohm.
Using this theory, we can measure the capacitor is bad/ damaged or good in condition.
Because our ESR meter only applies less than 15mV DC or peak to peak on a good capacitor, as a result we can use it as in circuit test. Because this low testing voltage, it cannot turn on the semiconductor inside a circuit under testing.
During repairing TV, LCD, Audio board, etc. we can in circuit testing the capacitor is good or not.
Dual terminal, for fast and easy inspect general capacitor or resistor, a printed ESR table for fast check
Compare MESR100 old V1 and new V2 Improvement:
1) Change square wave to sine wave 100 KHz, reduce square wave¡¯s high frequency component, and affect the reading passing the test leads and capacitor.
2) Higher Resolution up to 0.001 ohm.
3) 128X64 dot matrix LCD, with more larger value display and information
4) Embedded 25V capacitor table at LCD, auto display the capacitor is good or bad reference to common 25V electrolytic capacitor.
5) New plastic case, curve design for hand carrying. New stand for 60 degree stand on desk.
6) Use 2X AA battery, more convenience and longer battery life than 9V battery.
7) Support external USB power, using standard micro-USB port.
Specification:
Range
Accuracy (After Zero, tested with 1,10,100R resistor)
Refresh Time (Manual Mode)
Auto mode take 0 to 2s more time depend on value
0.000 to 1.000R 1%+2Digit ~0.4s
1.000 to 10.00R 1%+1Digit ~0.4s
10.00 to 100.0R 2%+1Digit ~0.4s
Accuracy maybe affected by the test lead¡¯s length and contact point resistance.
Standard test leads is 15cm, for longer test leads need special shielding to affect the EMI inference (Can contact sales¡¯ person for more detail)
1) Accuracy: Up to 1% (detail on above table)
Wide Measurement Range: >1uF (for 0.1uF the error will be larger on equation 1/(2*pi*F*C) @ 100Khz )
2) High Resolution: 4 digit, or 0.001Ohm @ 1 Ohm range
3) Measuring voltage: <~40mV RMS (TESTING VOLTAGE)
4) Clamping voltage: ~0.15V (open voltage)
5) Battery 2X AA 1.5V battery
6) External Power: 5V micro USB
7) Operating current 0.02A
8) Battery Life time: >80 Hours
Operating Introduction:
1) POWER ON
Press and hold the ON/ OFF circle orange button for 2 to 3 second to power on.
Press and release the ON/ OFF button to shut down meter.
2) AUTO/ MANUAL mode:
i) Auto Range:
Press and release the RANGE button and at the first line of LCD will show ¡°AUTO:"
At auto mode meter will automatically select the best range to detect.
ii) Manual Range:
Scroll the manual range from 1R, 10R and 100R range by press and release the RANGE button
In LCD will show MANUAL at first LCD line and show at second line: 0-1R, 1-10R and 10-100R.
3) 1 Key Zero:
Short circuit the test leads¡¯ terminal, cancelling the wire resistance.
Press and release the ¡°ZERO" button, LCD shows ¡°ZERO" and wait the zero disappear.
If you are using the meter array socket, you need to use a short pin to short circuit to set zero.
4) Backlight:
LCD backlight will on during power on
5) Auto Sleep:
Around 10 hours for not testing, it will shut down automatically to save power.
6) OVERFLOW or OL:
Display overflow when the value is out of range, you can check that you are zero correctly.
7) ESR TABLE:
It is for reference only, different manufacturer of capacitor has different ESR, better to test a good cap ESR and compare with what you are testing, usually bad cap with higher ESR few times larger than good one.
8) SOFTWARE ESR:
Put the 25V Electrolytic capacitor value to LCD, and compare,
GOOD if C < XXuF, means the capacitor maybe good condition if it is less than XXuF
9) PLASTIC STAND:
If you don¡¯t use the stand, press and push the lock position
Specification:
| Package Weight |
|
Shipping
Shipping policy
We offer fast and reliable shipping for all our clothing items. Orders are processed within 2-3 business days and shipped via standard delivery, which typically takes 8-25 business days.
Express shipping options are also available at checkout for an additional fee, ensuring your fashion essentials arrive even sooner. For any questions regarding your order, please contact our customer service team for assistance.
| Shipping from Chinese Warehouse： | ||
| Airmail and register airmail | Area | time |
| United States, Canada, Netherlands, Spain, Germany, France, Japan, Republic of Korea, United Kingdom | 7-15 business days | |
|
Australia ,New Zealand, Singapore |
7-15 business days | |
| Belgium, Denmark, Finland, Ireland, Norway, Portugal, Sweden, Switzerland | 7-20 business days | |
| Brazil, Russia, Mexico | 15-35 business days | |
| Other countries | 7-25 business days | |
| EMS | All countries except those listed below | 6-8 business days |
| Brazil and Russia | 10-25 business days | |
| Expedited Shipping*(DHL) | 3-7business days to worldwide. | 3-7 business days |
Return & Refund
Refund policy
We have a 30-day return policy, which means you have 30 days after receiving your item to request a return.
To be eligible for a return, your item must be in the same condition that you received it, unworn or unused, with tags, and in its original packaging. You’ll also need the receipt or proof of purchase.
To start a return, you can contact us at support@reluova.com. Please note that returns will need to be sent to the following address:
T8 BLOCK ROOM312,XINGHUA SMART ZOOM,DONG CHENG STREET,DONGGUAN,DONGGUAN,CHINA,523000,+86 137 9069 5247
If your return is accepted, we’ll send you instructions on how and where to send your package. Items sent back to us without first requesting a return will not be accepted.
You can always contact us for any return question at support@reluova.com.
Damages and issues
Please inspect your order upon reception and contact us immediately if the item is defective, damaged or if you receive the wrong item, so that we can evaluate the issue and make it right.
Exceptions / non-returnable items
Certain types of items cannot be returned, like perishable goods (such as food, flowers, or plants), custom products (such as special orders or personalized items), and personal care goods (such as beauty products). We also do not accept returns for hazardous materials, flammable liquids, or gases. Please get in touch if you have questions or concerns about your specific item.
Unfortunately, we cannot accept returns on sale items or gift cards.
Exchanges
The fastest way to ensure you get what you want is to return the item you have, and once the return is accepted, make a separate purchase for the new item.
European Union 14 day cooling off period
Notwithstanding the above, if the merchandise is being shipped into the European Union, you have the right to cancel or return your order within 14 days, for any reason and without a justification. As above, your item must be in the same condition that you received it, unworn or unused, with tags, and in its original packaging. You’ll also need the receipt or proof of purchase.
Provided the conditions in our refund policy have been met, refunds will be processed using the original form of payment. You can return an item purchased online by posting it to us. Please contact customer service for return address. Please note that delivery costs will be excluded from the refund unless goods are returned in accordance with your statutory rights (e.g. they are faulty or not as ordered).
Reviews
Wishlist
Wishlist is empty.
Compare
Shopping cart